Msd 8987 Start and Step Timing Control Installation Manuel d'utilisateur télécharger pdf

Figure 1

Parts Included:

1 – Control

4 – Mounting Screws

WARNING: During installation, disconnect the battery cables. When disconnecting the

battery, always remove the negative cable ﬁrst and install it last.

Note: Must be used with an MSD Ignition.

OPERATION

The Start and Step Retard provides two retard

features; a start retard and a step retard. The

Control can be connected to distributors using

a magnetic pickup, ampliﬁer or breaker point. It

is recommended that the centrifugal advance

of the distributor be locked-out. The amount

of retard is selected with the two rotary dials

(Figure 1).

Start Retard: The Start Retard is adjusted with the

rotary dial on the left. It is adjustable in 5° increments

for 4, 6 or 8-cylinder engines from 0°-20° The

number of cylinders must be selected, even when

no start retard will be used. Simply rotate to dial to

the desired position.

The Start Retard is activated as soon as the engine

begins to crank. Between 400 and 600 rpm, the

timing begins to ramp back to zero retard (your total

timing setting). The start retard will not activate again until the engine rpm drops to 400 rpm (the timing will

also ramp on again between 600-400 rpm).

Step Retard: The Step Retard is adjusted with the dial on the right. The retard is adjustable from 0°-

15° in one degree increments. The Step Retard is activated by the Pink wire. When the Pink wire is

connected to 12 volts, the retard is activated. The most common application is to splice the Pink wire

into the activation trigger wire of a nitrous system. That way, the retard is activated with the nitrous.

The Controller also has a very accurate magnetic pickup compensation circuit built-in and will hold

the timing steady throughout the entire rpm range of the engine. This is why there will be a 4° change

in the engine timing when the Control is installed.

Important: After installation the engine’s mechanical timing must be checked and reset.

6-CYLINDER

ENGINE

4-CYLINDER

ENGINE

ZERO

STEP RETARD

8-CYLINDER

ENGINE

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered

in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product

will help if there is ever a warranty issue with your product and helps the MSD R&D team create

new products that you ask for! Go to www.msdperformance.com/registration.

Start and Step Retard Control

PN 8987

1 2 3 4

Résumé du contenu

Page 1 - Start and Step Retard Control

Figure 1Parts Included: 1 – Control 4 – Mounting ScrewsWARNING: During installation, disconnect the battery cables. When disconnecting the

Page 2 - WIRING:

2 INSTALLATION INSTRUCTIONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 3 - TECH NOTES

INSTALLATION INSTRUCTIONS 3M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 4

Limited Warranty MSD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installe

Commentaires sur ces manuels

Pas de commentaire

Msd 8987 Start and Step Timing Control Installation Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Msd 8987 Start and Step Timing Control Installation. MSD 8987 Start and Step Timing Control Installation User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Msd 8987 Start and Step Timing Control Installation