Msd 7562 Programmable Launch Boost Controller Installa Manuel d'utilisateur télécharger pdf (Page 1)

MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

Parts Included In This Kit

1 - Controller

4 - Mounting Screws

1 - Wiring Harness

1 - Solenoid Valve Assembly, ASY25190

Programmable Launch Boost Controller

PN 7562

Parts Required but Not Supplied:

1 - MAP Sensor:

2 BAR Up to 30-psia, MSD PN 23121

3-BAR Up to 45-psia, MSD PN 23131

75-PSIA Up to 75-psia Absolute pressure

75-PSIG Up to 75-psia Gauge pressure

The MSD Programmable Launch Boost Controller allows you to program a boost pressure map

from the launch through a complete run from 12.5 to 100 seconds. You can also program a boost

limit during the burnout. The boost pressure is controlled through two PWM outputs that control

two normally closed 2-way, solenoid valves connected to the waste gate actuator. The actuator is

programmed through PID servo-control and can be tuned for the particular actuator response.

The Boost Controller also can record from 20 to 160 seconds of data including engine rpm, map

pressure, Boost Curve Pressure, Barometric Pressure, PWM output and the Launch and Overboost

input wires. This can all be saved and reviewed in the Launch History window of the MSD software.

All of the programming features can be set with the MSD Pro-Data+ software. This software is for

PCs running Windows 95, 98, 2000, NT, XP or ME. All of the parameters can be saved in the PC,

then uploaded to the Controller. There is also a Hand Held Programmer/Monitor, PN 7550, that is

available separately. This unit has an LCD display that will walk through the programming menus

for programming without a PC.

PROGRAMMABLE FEATURES

BURNOUT

This determines how the Light Blue Burnout wire is activated. It can either be activated by applying

12 volts or by switching it to ground. Default is 12 volts.

SwPWR 12 volts activation

SwGND Ground activation

BOOST

Program a boost map based on time from 12.5, 25, 50 or 100 seconds. Also, select a maximum

boost pressure for the burnout.

Launch: This is the map for the run. This program is made on the Boost Pressure Curve

graph. The Boost pressure can be plotted over time down to 0.01-second and 0.1-psia

increments. One to thirty-two points may be set in the graph.

Burnout: Select a maximum boost pressure that will be used during the burnout. Adjustable

from 0 - 75-psia.

Overboost: This selection lets you program a rampable boost value that is higher than the

programmed curve. Overboost is only activated when its activation wire (Orange) is switched

to 12 volts.

Max: This adjustment extends the time that you can program a boost curve. Adjustable in

12.5, 25, 50 or 100 seconds.

1 2 3 4 5 6 ... 23 24

Résumé du contenu

Page 1 - PROGRAMMABLE FEATURES

MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344Parts Included In This Kit1 - Controller4 - Mounting

Page 2 - 2 INSTALLATION INSTRUCTIONS

10 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344SETTING MINIMUM BOOSTIf y

Page 3 - INSTALLATION INSTRUCTIONS 3

INSTALLATION INSTRUCTIONS 11MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344Figure 6TEST EXAMPLE 1 -

Page 4 - OPERATION AND SET UP

12 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 2 - FIGURE 7

Page 5 - INSTALLATION INSTRUCTIONS 5

INSTALLATION INSTRUCTIONS 13MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 3 - FIGURE 8

Page 6 - SEQUENCE OF EVENTS

14 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 4 - FIGURE 9

Page 7 - ACQUISITION

INSTALLATION INSTRUCTIONS 15MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344Figure 10TEST EXAMPLE 5 -

Page 8 - GETTING STARTED AND TUNING

16 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 6 - FIGURE 1

Page 9 - CONFIRM OPERATION

INSTALLATION INSTRUCTIONS 17MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 7 - FIGURE 1

Page 10 - SETTING MINIMUM BOOST

18 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 8 - FIGURE 1

Page 11 - TEST EXAMPLE 1 - FIGURE 6

INSTALLATION INSTRUCTIONS 19MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 9 - FIGURE 1

Page 12 - TEST EXAMPLE 2 - FIGURE 7

2 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344SENSORSelect the type of M

Page 13 - TEST EXAMPLE 3 - FIGURE 8

20 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TEST EXAMPLE 10 - FIGURE

Page 14 - TEST EXAMPLE 4 - FIGURE 9

INSTALLATION INSTRUCTIONS 21MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

Page 15 - TEST EXAMPLE 5 - FIGURE 10

22 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TECH NOTES_______________

Page 16 - TEST EXAMPLE 6 - FIGURE 11

INSTALLATION INSTRUCTIONS 23MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344TECH NOTES_______________

Page 17 - TEST EXAMPLE 7 - FIGURE 12

MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344FRM25290 Created 07/04 Printed In U.S.A.Limited Warra

Page 18 - TEST EXAMPLE 8 - FIGURE 13

INSTALLATION INSTRUCTIONS 3MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344LEDThe LED on the side of

Page 19 - TEST EXAMPLE 9 - FIGURE 14

4 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344Figure 1 Wiring the Boost

Page 20 - TEST EXAMPLE 10 - FIGURE 15

INSTALLATION INSTRUCTIONS 5MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344Figure 2 Single Port Waste

Page 21 - INSTALLATION INSTRUCTIONS 21

6 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344SEQUENCE OF EVENTSThe sequ

Page 22 - TECH NOTES

INSTALLATION INSTRUCTIONS 7MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344When the brakes are applie

Page 23

8 INSTALLATION INSTRUCTIONSMSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344Both boxes have an On and

Page 24

INSTALLATION INSTRUCTIONS 9MSD IGNITION • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344CONFIRM OPERATIONPrior to

Commentaires sur ces manuels

Pas de commentaire

Msd 7562 Programmable Launch Boost Controller Installa Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Msd 7562 Programmable Launch Boost Controller Installa. MSD 7562 Programmable Launch Boost Controller Installation User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Msd 7562 Programmable Launch Boost Controller Installa Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Msd 7562 Programmable Launch Boost Controller Installa. MSD 7562 Programmable Launch Boost Controller Installation User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Msd 7562 Programmable Launch Boost Controller Installa