Msd 8202 Blaster 2 Coil Hi-Performance Installation Manuel d'utilisateur télécharger pdf

Parts Included:

1 - Blaster Coil, PN 8202, PN 8223, PN 8222

2 - Brass Nuts and Lock Washers

Note: This Blaster Coil Kit is intended to be used with an MSD Ignition. If installing on a stock, points

style ignition system, a 0.8 ohm ballast resistor or resistor wiring MUST be installed. MSD offers

this Ballast Resistor as PN 8214 or the Blaster Coil Kits, PN 8200 and 8203 are equipped with one.

WARNING: Failure to use a ballast resistor could result in personal injury or component failure.

The Blaster Coil is designed to mount in most factory canister coil mounts. MSD also offers a Chrome

Coil Bracket, PN 8213. It is recommended to mount the PN 8202 and 8223 coils in an upright position.

The High Vibration Coil, PN 8222, can be mounted in any position due to its epoxy potting compound.

INSTALLATION

WARNING: During installation, disconnect the battery cables. When disconnecting the battery,

always remove the Negative (-) cable ﬁrst and install it last.

1. Mark the original coil wires as positive (+) and negative (-) and remove the wires.

2. Remove the high voltage coil wire (spark plug wire) and remove the coil from the bracket.

3. Install the Blaster Coil into the mount and tighten.

WIRING TO AN MSD 6 OR 7 SERIES IGNITION

The MSD 6 and 7 Ignitions are Capacitive Discharge Ignitions. They receive 12 volts directly from the

battery and are responsible for delivering the positive voltage to the coil. Therefore, a 12 volt source

wire is not required at the coil. When the installation with an MSD Ignition is complete, there will only be

two wires making direct contact to the coil terminals: The Orange Wire from the MSD connects to the

coil positive (+) terminal. The small Black wire from the MSD connects to the coil negative (-) terminal

(Figure 1).

Figure 1 Wiring to an MSD 6 or 7 Series Ignition Control.

PN 8202/8223/8222

MSD Blaster Coil

PN 8202, PN 8223

High Vibration Blaster Coil, PN 8222

(PN 8223 also is supplied with a

90° Plug Terminal and Boot)

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered in our

monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if there

is ever a warranty issue with your product and helps the MSD R&D team create new products that you

ask for! Go to www.msdperformance.com/registration.

1 2

MSD Blaster Coil 1

Résumé du contenu

Page 1 - MSD Blaster Coil

Parts Included:1 - Blaster Coil, PN 8202, PN 8223, PN 82222 - Brass Nuts and Lock WashersNote: This Blaster Coil Kit is intended to be used with an MS

Page 2

WIRING TO A STOCK POINTS IGNITION 1. Connect the negative wire to the negative terminal (-).2. Connect a wire from the coil positive terminal to one s

Commentaires sur ces manuels

Pas de commentaire

Msd 8202 Blaster 2 Coil Hi-Performance Installation Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Msd 8202 Blaster 2 Coil Hi-Performance Installation. MSD 8202 Blaster 2 Coil Hi-Performance Installation User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Msd 8202 Blaster 2 Coil Hi-Performance Installation