Msd 82921 Distributor Cap, Modified for Civic_Integra Manuel d'utilisateur télécharger pdf

Parts Included In This Kit:

1 - Distributor Cap

1 - Coil Wire

MSD Modiﬁed Honda Distributor Cap

PN 82901, PN 82902, PN 82921 and PN 82922

WARNING: During installation, disconnect the battery cables. When disconnecting the battery

cables, always remove the Negative cable ﬁrst and install it last.

1 - Parts Bag

1 - Mini-Stripper-Crimper

Note: The Modiﬁed Cap is designed so that you can remove the stock internal coil, and use a higher

output external coil. The stock internal coil MUST be removed before the installation of this

Figure 1 Primary Wiring with the Coil Removed.

Figure 2 Wiring with a Blaster SS Coil.

1 - Retainer and Screw

(Extreme Caps only)

cap. Failure to do so will cause damage

to the MSD cap.

Note: The supplied spark plug style terminals

are required with the PN 82902 and PN

82922 caps.

INSTALLATION:

1. Mark the location of each plug wire, then

remove the wires. Remove the stock distributor

cap, rotor and dust cover.

2. Locate the coil wires and note their color and

location. On the majority of Honda or Acura

engines, the Black/Yellow wire is positive. The

coil negative wire is generally White/Blue, Blue,

Green/Yellow or Green. In some cases, the coil

itself is marked negative (-) and positive (+).

Note: If you have a question as to the

wires’ polarity, use a volt-meter and

probe each wire with the ignition

key turned to the On position. Coil

positive will show 10-12 volts.

3. Once you determine the polarity of the

coil wires you will need to extend the

wires to reach the MSD coil. Cut the

factory terminals off and solder to a 14

gauge wire. Seal the soldered joint with

shrink sleeve or electrical tape.

4. Depending on the model of distributor

you have, you may need to drill a hole

in the new cap to route the wires out.

In some applications the factory rubber

seal is thick enough to cut and slide the

new wires out.

5. Install the rotor, the new cap and then

the wires. For Extreme model caps, install the wire retainer with the supplied screw.

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

1 2 3 4

Résumé du contenu

Page 1 - INSTALLATION:

Parts Included In This Kit:1 - Distributor Cap1 - Coil WireMSD Modiﬁed Honda Distributor CapPN 82901, PN 82902, PN 82921 and PN 82922 WARNING: During

Page 2 - STRIPPING THE WIRE

2 INSTALLATION INSTRUCTIONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 3 - TERMINAL

INSTALLATION INSTRUCTIONS 3M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 4 - ALIGNMENT TABS

Figure 9 Crimping the Terminal.ALIGNMENT TABS6. Slowly close the vise making sure the tool and terminal stay properly positioned and aligned. Stop app

Commentaires sur ces manuels

Pas de commentaire

Msd 82921 Distributor Cap, Modified for Civic_Integra Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Msd 82921 Distributor Cap, Modified for Civic_Integra . MSD 82921 Distributor Cap, Modified for Civic_Integra LS 92-00 Installation User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Msd 82921 Distributor Cap, Modified for Civic_Integra